NEXO DTDAMP4X1.3

NEXDTDAMP4X13C

Two models of high-power, lightweight four channel amplifiers
Perfect match for the NEXO speakers supported by the DTD Controller
High-efficiency Switch Mode power supply and Amplifier channel design
Channels can be independently bridged two by two
Four Inputs on XLR connectors and four Outputs on SP-4 connectors
Extensive protection (Mains over/ undervoltage, temperature, DC outputs, current and voltage peak limiters, variable speed cooling system)


€ 2.314,81
prijzen incl. taksen en BTW

Tijdelijk niet op voorraad

DTDAMP4X1.3

The DTDAMP range is composed of two models of four channel amplifiers housed in a 1U rack and weighting only 7.5 Kg. The DTD Controller offers a very efficicent solution for processing most of the Nexo Speakers, from the ID series to our world famous PS15. When used with a DTDAMP you are sure to get all the necessary power for your NEXO speakers, while this combo offers both a coherent look and ease of use. A pair of DTD + DTDAMP will weigh together less than 10 Kg, while being able to process and power system composed, for example, of 2 x NEXO Speakers + 2 x NEXO subs. This performance is due to the use of high-density and highly integrated components together with high-efficiency design (smaller heatsinks) for power supply/power amplifier parts. The DTDAMP offers all the sensor and protection that are mandatory for a professional touring amplifier, such as mains over/under voltage, Over-voltage or DC output on each channel, short circuit etc. The variable speed cooling system will assure a quiet and cool amplifier while the front to back cooling system ensure compatibility inside racks where both DTDAMP and our high-end NXAMP are used together in large installations. Once your NEXO Speakers are selected in your DTD Controller, you can use your DTD +DTDAMP system in most situations without any further adjustments to the settings. When used with the NEXO DTD controller the DTDAMP is the perfect solution for “Dry” hire or where the user has a limited knowledge but still allowing the best possible result from the Nexo speaker system.

KEY FEATURES

Two models of high-power, lightweight four channel amplifiers

Perfect match for the NEXO speakers supported by the DTD Controller

High-efficiency Switch Mode power supply and Amplifier channel design

Channels can be independently bridged two by two

Four Inputs on XLR connectors and four Outputs on SP-4 connectors

Extensive protection (Mains over/ undervoltage, temperature, DC outputs, current and voltage peak limiters, variable speed cooling system)

SPECIFICATIONS

Number of channels 4 x amplifiers channel, 2 by 2 bridgeable

Max. output voltage (no Load) 4 x 135 Volts

Max. output power (4 x 8 Ohms) 4 x 750 Watts

Max. output power (4 x 4 Ohms) 4 x 1300 Watts

Max. output power (2 brigde x 8 Ohms) 2 x 2600 Watts

Frequency response +/- 0.5 dB from 20 Hz to 20 kHz

Input impedance 10 kOhms

Input sensitivity +8 dBU

Nominal Gain 32 dB

Dynamic Range (A-weighted) > 110 dB

THD+N Typical 0.01%

FEATURES

Analog audio inputs 4 x balanced analog inputs on XLR

Power outputs 4 x SP4 outputs

Link switch To use same XLR input for 2 x adjacent channels

Mains sockets IEC C14 Inlet with secure lock

Switch and knobs Mains On/Off switch and volume control knob per channel

View meters 4 x LEDs (signal / -18 dB / -6 dB / Peak) per channel

Amplifier status Amp Ready and Temperature indicator per channels pairs

Mains voltage Factory set for 120 volts of 230 volts mains operation

Power consumption (Idle) 65 Watts

Power consumption 1/8 max. / 4 Ohms 900 Watts

Power consumption 1/4 max. / 4 Ohms 1800 Watts

Dimensions (W x H x D) 480 (W) x 44 (H) x 370 (D) mm, 19 inches / 1U

Weight 7.5 kg

Operating temperature range 0°C - 45 °C

CE conformity 2006/95/CE (Low voltage) 2004/108/CE (EMC) 2002/95/CE (RoHS)

Electrical safety certification CSA, CB, EN60065

EMC certification EN55103-1 / EN55103-2 / FCC