The Radial Headbone is a specially designed switching device that lets you toggle between two different guitar amplifier heads using a single speaker cabinet. With the Headbone in your rig, you can use your Marshall head for rhythm and your Mesa-Boogie head for soloing.

Radial Headbone TS Guitar Amp Head Switcher from 1 Tube to 1 Solid-State Amp.

The Headbone VT is a specially designed switching device that lets you toggle between two tube amplifier heads using a single speaker cabinet. This provides the ability to experiment with different tonal options and perform without hauling two speaker cabinets to the gig.

The Headlight is a unity gain guitar amp selector designed to easily integrate onto a pedalboard and provide the ability to switch between as many as four amplifiers with a single footswitch.

The Headload Prodigy™ is a combination load box and DI that lets you drive your guitar amp at a higher gain in order to maximize the tone, yet produce a lower stage volume when needed.

Several Radial products such as the Firefly, Gold Digger and Cherry Picker may be rack-mounted for use in live touring or to fit in studio racks equipped with standard 19″ rail systems. Others, such as the SixPack and Cube, may also be mounted into a desk top to optimize ergonomics and studio efficiency.

The SA series rack adapter is a dual function angle bracket that may be used to mount one or two Radial Stand Alone (SA) series devices such as the Gold Digger, Cherry Picker and Phazer along with other Radial products like the Firefly into a standard 19″ rack frame. The 1 RU adapter comes complete with mechanical mounting screws, hex wrench, two angle brackets and a center cube attachment when fitting two devices side by side.

Combination load box and DI with speaker emulation
Available in 4, 8, or 16 Ohms
Can handle up to 130 watts RMS (180 peak)
Attenuate down to 1% of total power

Speaker load box,8 ohms,w.Radial JDX cab sim.

Guitar signal distribution system

Radial - RADPASDI - Passive Stereo DI with Jensen transformers

Active Class A DI, 2-in/4-out, DISCONTINUED

JDX 500 Amp Sim.w.Reactive Load

Radial - RADACTDI - Guitar Amp simulator w.3 amp settings&bal. DI out

Active Class A reactive speaker emulation DISCONTI

Mic preamp,Jensen 990 opamp,dual Jensen transf.

Radial - ACCESS - Latching footswitch w.active(LED)or passive circ.

Radial - ACCESS - Momentary footswitch w.active(LED)or passive circ.

The Radial J-Rak is a 2RU rack shelf that allows as many as 8 Radial direct boxes to be rack mounted. These can face forward (input at front) or backward (XLRs at front), active (J48) or passive (JDI) in any combination, depending on the system designer's preference. The J-Rak also fits the Radial X-amp re-amplifying device and future Radial interface products to come!

Radial - ACCESS - Rackmount 1RU for 4 DI boxes

Radial - ACCESS - Rackmount 2RU for 8 DI boxes

Radial - REAMP - 4x2 Discrete Class-A guitar & amp switcher

Guitar selector,4 inputs w.AB amp isolated outputs

Radial - RADSPLIT - Active Class A guitar distro system 4in/4out PSU

Air Control™ Guitar Signal Manager

Radial - RAD500SER - Komit 500 VCA Comp.w.Discrete Lim

-Audio circuit type: Passive, transformer based
-Transformer: Jensen JT-123-FLPCH
-Number of channels: 1 In, 3 Out
-Frequency response: 20Hz - 20kHz +/-0.5dB
-Dynamic range: 140dB
-Gain: -1.5dBu
-Phase Deviation: +0.6° @ 20Hz
-Input Impedance: 712?
-Output Impedance: 112?
-Common Mode Rejection Ratio: 105dB @ 60Hz, 70dB @3kHz
-Noise: -120dBu
-Maximum Input: +20dBu

Radial - RADSWITCH - Studio monitor controller

The Mix-Blender™ is a multi-function pedal that lets you mix two instruments or pedals together and then send the signal through a footswitch-controlled effects loop for processing.